Select a waveguide quick disconnect by its exact mating interface, locking arrangement and verified RF performance after reconnection. For a pressurized line, add separate pressure and leakage limits. A fast latch does not establish flange compatibility, low insertion loss or a gas-tight seal.
| Selection gate | Evidence to request |
|---|---|
| Compatible interface | Dimensioned aperture, flange, locating features, ridge orientation and seal drawing. |
| Secure assembly | Locked-position criteria, installation clearance, allowable loads and assembly procedure. |
| RF performance | Full-band transmission and reflection measurements at stated reference planes. |
| Repeated connections | RF results and mechanical inspection after the specified connection cycles. |
| Pressure retention, if required | Rated pressure, approved seal and leakage result with stated test conditions. |
Flange Compatibility
Table of Contents
Flange Size Matching
WR90, WR28 and WRD650 identify waveguide sizes or families. They do not fully specify the flange hole pattern, seal groove, alignment arrangement or locking geometry. Obtain both mating drawings before choosing the quick disconnect.
IEC 60154-2:2016 covers flange dimensions and mechanical requirements for ordinary rectangular waveguides. Its scope does not establish compatibility for every double-ridged or proprietary interface.[1] Where an EIA or IEC flange is specified, include the exact designation and applicable drawing revision.
Check aperture width and height, flange thickness, ridge dimensions where present, and the orientation of every feature. Overlapping frequency bands do not make an ordinary rectangular interface interchangeable with a double-ridged one.
Dolph’s quick disconnect assembly table lists WRD840 through WRD180 models with model-dependent VSWR values of 1.15:1 or 1.2:1 and flat/cover or grooved flange codes. Select the individual row that covers the required band; these values do not establish a pressure rating or insertion-loss limit.
Bolt-Hole Position Check
Compare hole count, center spacing, diameter, thread, counterbore and locating-pin engagement. Reference their positions to the RF aperture, not just the flange outside edge. The locking mechanism should draw aligned faces together without forcing the waveguide sideways.
IEC 60154-2 recommends post-drilling alignment holes after the flange is mounted for optimum electrical performance. For procurement, ask how the finished interface is located and inspected rather than assuming that a machined flange blank proves assembled alignment.
Check latch or thumb-screw clearance with the adjacent hardware and supports installed. A connection that works on an open bench may become inaccessible inside the equipment.
Sealing Face Fit
Identify whether the joint uses flat contact faces, a grooved flange and seal, or a choke interface with a specified mating face. A choke interface can use a designed gap; applying a generic “all faces must touch” rule can defeat the intended geometry.
Reject burrs, damaged locating features and contamination that prevent the specified fit. Inspect sealing lands for scratches and check the groove, seal cross-section and compression limits against the drawing. Extra clamp force cannot repair incompatible faces.
Select the gasket or O-ring by its approved compound and service conditions: temperature, gas compatibility, compression set and any conductivity or outgassing requirement. “Silicone” alone does not specify those properties. A grooved flange is not automatically pressure-tight.
Fast Assembly
Tool-Free Locking
Dolph describes a thumb-screw clamping arrangement for its listed quick disconnects. Confirm the required engagement, stop or locking indication and any secondary retention. Do not assume “tool-free” means that tightening force is self-controlled.
- Check that the lock can be operated with the intended gloves and available hand clearance.
- Verify that nearby cables or hardware cannot release it accidentally.
- Define the allowed tightening torque or locking procedure where required by the design.
- Support adjoining waveguide sections so external bending and torsion stay within the joint’s allowed loads.
Before opening a pressurized or powered assembly, isolate RF and depressurize it using the approved procedure. After reconnection, verify alignment, the seal and the fully locked state before restoring service.
Repeatable Connection
One passing RF sweep shows one connection condition. It does not show how the interface behaves after repeated removal, wear, contamination or changes of operator.
Define one connection cycle as a disconnect-and-reconnect operation, then state the required count and inspection intervals. An illustrative maintenance schedule of two connections per working day over 250 days gives 500 connections per year; this calculation sets a demand, not a product life rating.
- Measure the initial full-band S-parameters using the approved setup.
- Disconnect and reconnect with the specified procedure and representative support loads.
- Repeat for the agreed cycle count, measuring at defined intervals.
- Inspect locating features, locking parts, contact surfaces and seals.
- Compare RF changes and leakage, where applicable, with the acceptance limits.
Record seal replacement during the test. A result achieved with a new seal at every connection does not demonstrate the same endurance as repeated use of one seal.
Field Installation Time
State what the stopwatch includes: moving the sections into place, removing covers, cleaning, fitting the seal, locking, inspection and any required testing. Report mechanical closure time separately from time to return the system to service.
Use the same representative layout and procedure for each candidate. Record the number of trials, median time, slowest successful trial and failed attempts. A claimed 70% saving needs a documented baseline and the same completion criteria; the fastest latch movement alone is not that evidence.
Signal Integrity
Low Insertion Loss
For a matched two-port measurement, insertion loss is −20 log10|S21| in decibels. Return loss is −20 log10|S11| at port 1, with port 2 terminated in the reference impedance. Lower insertion loss and higher return loss are preferable; they measure different effects.
The reflected-power fraction corresponding to VSWR is [(VSWR − 1)/(VSWR + 1)]². Thus, VSWR 1.15:1 corresponds to about 0.49% reflected power, and 1.2:1 to about 0.83%. These calculated values do not include dissipation and cannot be used as insertion-loss specifications.
Request S11 and S22 at both ports and S21/S12 where applicable, with frequency spacing, calibration method, reference planes and measurement uncertainty. NIST research demonstrates how imperfect waveguide test-port interfaces can create calibration inconsistencies; keep those interfaces controlled when comparing reconnect measurements.[2]
Good Contact Pressure
For a contact-type joint, insufficient or uneven force can leave gaps; excessive force can distort the flange, damage threads or overcompress the seal. For a choke joint, maintain its specified spacing and contact arrangement. There is no universal clamp-force value for every flange.
Validate the locking procedure through dimensional checks and repeated RF measurements. Where vibration or temperature cycling is part of service, check the locked state and RF performance after the specified exposure. Any pressure-sensitive film used during development must be compatible with the surfaces and removed before final RF assembly.
Leakage Control
RF leakage and gas leakage require different evidence. S-parameter measurements can reveal transmission or reflection problems, but they do not locate escaping RF fields or by themselves prove compliance with an RF leakage limit. Use the specified leakage measurement under defined power, frequency and probe conditions.
For gas retention, specify maximum operating pressure, pressure-test conditions, gas, temperature and allowable leak rate with units. A visible O-ring or a good VSWR result does not establish gas-tightness.
ISO 20485:2017 covers leak detection using a tracer gas and a detector specific to that gas.[3] If that method is selected, define detector calibration, background, stabilization time and acceptance criteria in the procedure. Pressure-decay measurements also need temperature control or correction so thermal drift is not mistaken for leakage.
Include the assembly identity, interface drawing, locking condition, cycle count, RF plots and applicable leakage results in the acceptance report. A low-power RF test and a separate room-temperature leak test do not automatically qualify combined high-power, pressure and temperature conditions.
For a custom quick-disconnect assembly, send the mating drawings, operating band, power, available clearance, connection schedule and pressure requirements. Ask Dolph to confirm the interface and proposed verification plan before the locking mechanism is released for manufacture.