HOME » What Is EIRP in a Satellite Link Budget?

What Is EIRP in a Satellite Link Budget?

What Is EIRP in a Satellite Link Budget?

Effective isotropic radiated power (EIRP) is the power an ideal antenna radiating equally in all directions would need to produce the same power density as the actual antenna, at the same distance in the direction of the link. It is the transmit-side starting point for calculating received power: add receive antenna gain and subtract the losses between the radiated signal and the receiver input [1] [2].

How to Calculate EIRP

EIRP (dBW) = transmitter output power (dBW) + transmit antenna gain (dBi) − transmit feed loss (dB). Use the gain in the direction of the receiving station at the operating frequency. The feed loss covers the path from the transmitter output to the antenna input, including any waveguide sections on that path. If the power figure is already specified at the antenna input, add the antenna gain without subtracting that loss again [2].

Worked Example

Assume 10 W (10 dBW) at the transmitter output, 1 dB of feed loss, and 30 dBi of antenna gain. The result is 10 − 1 + 30 = 39 dBW. If a worksheet instead starts with 9 dBW at the antenna input and gives 38 dBW, check whether the 1 dB feed loss was counted twice.

To check in watts, multiply the transmitter output by the linear antenna gain and divide by the linear loss factor: 10 × 1,000 ÷ 1.2589 ≈ 7,943 W. That is isotropic-equivalent power in the link direction, not the total power radiated by the antenna.

Illustrative EIRP calculations
Transmitter outputAntenna gainFeed lossEIRP
10 W30 dBi1 dB39 dBW (≈7.94 kW)
100 W35 dBi1 dB54 dBW (≈251 kW)
200 W30 dBi2 dB≈51 dBW (≈126 kW)

Watts, dBW, and dBm

Watts are a linear measure of power. dBW and dBm describe the same power on logarithmic scales with different references. Only those two readings are 30 dB apart: add 30 to convert dBW to dBm [2].

Three ways to express the same EIRP
UnitReferenceWorked example
WLinear power≈7,943 W
dBWRelative to 1 W39 dBW
dBmRelative to 1 mW69 dBm

EIRP density describes power per unit bandwidth. Check the reference bandwidth before comparing it with another density or with total carrier EIRP. For example, 54 dBW spread uniformly over 1 MHz averages −6 dBW/Hz. That average does not reveal the peak density of a nonuniform signal. Some earth-station rules express density in a specified bandwidth, such as dBW per 4 kHz [3].

EIRP vs. ERP

Effective radiated power (ERP) uses an ideal half-wave dipole as its gain reference (dBd). EIRP uses an isotropic radiator (dBi). With both powers expressed in dBW or both in dBm, EIRP = ERP + 2.15 dB. Likewise, an antenna gain of 30 dBd is 32.15 dBi; entering it as 30 dBi understates EIRP by 2.15 dB [4].

How EIRP Sets Received Power

Received power (dBW) = EIRP (dBW) − free-space path loss (dB) + receive antenna gain (dBi) − other applicable losses (dB). Define the receive reference point before including any receive-side feed loss. Account for pointing and polarization losses only if they are not already included in the gains or EIRP you used [2].

For an illustrative 12 GHz downlink, use 54 dBW of satellite EIRP, 205.1 dB of free-space loss, 45 dBi of receive gain, and an assumed 2 dB of additional loss. The resulting power at the chosen receiver input is 54 − 205.1 + 45 − 2 = −108.1 dBW. The 2 dB allowance is not a fade prediction. For a real availability target, use the Earth–space propagation methods in ITU-R P.618 and account for gaseous attenuation using ITU-R P.676. Keep modem implementation margin separate from received signal power [5] [6].

Free-Space Loss for GEO and LEO

Free-space path loss is approximately 92.45 + 20 log10(distance in km) + 20 log10(frequency in GHz). Use the slant range from the terminal to the satellite. The overhead examples use the nominal geostationary (GEO) altitude of 35,786 km and an assumed low Earth orbit (LEO) altitude of 550 km [7] [8].

Free-space loss for illustrative overhead paths
PathSlant range12 GHz30 GHz
GEO35,786 km205.1 dB213.1 dB
LEO550 km168.8 dB176.8 dB

At 12 GHz, the overhead LEO example has 36.3 dB less free-space loss than the overhead GEO example. Holding EIRP, receive gain, and the 2 dB allowance fixed gives −71.8 dBW for LEO. This isolates the effect of distance; it does not predict the difference between two operating networks.

Which EIRP Contour to Use

For a satellite downlink, read the operator’s EIRP contour for the receiving site and check what the map represents. Suppose the map shows 54 dBW at beam peak and 51 dBW at your site on the same carrier basis. With the rest of the worked budget unchanged, using 54 dBW would overstate received power by 3 dB: the site result would be −111.1 dBW rather than −108.1 dBW.

Confirm whether the figure is per carrier or for the full transponder, and whether it assumes saturation or operation with output back-off. For the uplink, use the earth station’s EIRP toward the satellite; the satellite’s downlink contour does not supply that number.

How to Raise EIRP

  • Raise transmitter output. Doubling RF output adds about 3 dB if antenna gain and feed loss stay fixed. Check the amplifier’s usable output at the required operating point.
  • Choose higher antenna gain. At the same frequency and aperture efficiency, a larger dish gives more peak gain and a narrower beam. A fixed-size dish can also give higher gain at higher frequency if efficiency holds, but the path loss and pointing budget must be reassessed [9].
  • Reduce feed loss. Check insertion loss at the operating frequency for cable, waveguide rotary joints, and waveguide diplexers. Recovering 1 dB of feed loss adds 1 dB to EIRP at the same transmitter output.

When comparing SATCOM antennas and antenna feed networks, record the frequency, the power and gain reference points, and which losses are already included. Compare the options on the same carrier basis and check the resulting EIRP against the applicable operating limits.

Discuss your EIRP budget with Dolph Microwave

Share your operating frequency, target EIRP, and available antenna size to discuss antenna, feed, and waveguide options.

Request a Link Review
latest news
Scroll to Top
Blank Form (#3)